Your Gutter Questions, Answered
100+ Gutter Questions Answered for Oregon's Central Coast
Click any question below to see the answer. Still have questions? Call us at (541) 270-6492.
Seamless aluminum gutters in Oregon typically run $8 to $15 per linear foot installed, depending on your home's height, roofline complexity, and the number of corners and downspouts. Copper gutters cost more, generally $25 to $40 per linear foot. We provide free on-site estimates with exact pricing before any work begins.
The main factors are linear footage, number of stories, roofline complexity (corners, angles, dormers), material choice, downspout count, and whether fascia repair is needed. Homes on steep lots or with limited access may also cost slightly more due to extra labor and equipment requirements.
Yes. Every estimate is free, on-site, and comes with no obligation. We measure your roofline, assess any existing damage, and provide a detailed written quote so you know exactly what you are paying for. Most estimates take about 30 minutes.
We do not have a strict minimum, but very small jobs under 40 linear feet may carry a slightly higher per-foot cost to cover setup and travel time. We are happy to provide a free estimate for any size project — from a single garage run to a full-home replacement.
We accept cash, check, and credit cards. For larger projects, we can discuss payment arrangements on a case-by-case basis. Contact us during your estimate to discuss options that work for your budget.
Gutter repairs typically range from $150 to $500 depending on the scope — resealing a joint, rehanging a sagging section, or replacing a damaged downspout. If repairs exceed 30 to 40 percent of the cost of new gutters, we usually recommend replacement for better long-term value.
We can give you a general ballpark range over the phone if you know your home's approximate linear footage and number of stories. However, an accurate quote requires an on-site visit to assess your roofline, fascia condition, and downspout placement. Our on-site estimates are always free.
We install seamless aluminum, copper, and galvanized steel gutters in both K-style and half-round profiles. Aluminum is our most popular option for Oregon homes because it resists rust, handles our heavy rainfall, and comes in a wide range of colors. We also offer 5-inch and 6-inch sizing to match your roof's drainage needs.
Yes. Aluminum is rust-resistant, lightweight, and handles salt air better than steel. It is our most-recommended material for Central Coast homes from Depoe Bay to Waldport because it withstands both heavy rain and the corrosive marine environment without degrading.
With proper installation and maintenance, aluminum gutters last 20 to 30 years on the Central Coast. Salt air and coastal winds can shorten lifespan slightly compared to inland homes, but regular cleaning and quality hangers keep them performing for decades.
Galvanized steel is strong and handles heavy loads, but it is more prone to rust than aluminum, especially in the salt-air environment near the coast. We generally recommend aluminum for homes in Newport, Lincoln City, and other coastal towns unless you need the extra strength for a commercial application.
Vinyl gutters become brittle in cold weather, warp in direct sun, and have seams at every joint that leak over time. Oregon's combination of heavy rain, freeze-thaw cycles, and UV exposure makes vinyl a poor long-term choice. Seamless aluminum outperforms vinyl in every measurable way in our climate.
Yes. We fabricate and install seamless copper gutters and downspouts. Copper develops a natural patina over time that complements Oregon's lush landscape, and it is extremely durable — copper gutters can last 50 to 100 years with minimal maintenance. They are a premium option ideal for historic homes and high-end builds.
Yes. Copper develops a natural patina that transitions from bright copper to brown and eventually to a distinctive green. This patina actually protects the copper from further corrosion and is considered a desirable aesthetic feature, especially on historic and Craftsman-style homes along the Oregon Coast.
Our aluminum gutters come in over 25 colors including white, cream, brown, bronze, black, gray, and forest green. We can match your trim, fascia, or siding for a seamless look. During your free estimate, we bring color samples so you can see the options against your home.
In most cases, yes. We carry over 25 standard aluminum colors and can match common trim and siding colors. If you bring us a paint chip or color code, we can find the closest match from our supplier's color chart. Custom powder-coating is available for exact matches on specialty projects.
Salt air accelerates corrosion on unprotected metals. Aluminum and copper resist salt air well, which is why we recommend them for homes in Newport, Depoe Bay, and other coastal communities. Galvanized steel and exposed iron fasteners are more vulnerable, so we use stainless steel screws and salt-rated hangers on all coastal installations.
Aluminum is the best all-around choice for beachside homes — it resists salt corrosion, handles heavy rain, and stays affordable. For premium coastal properties, copper offers unmatched durability and aesthetics. We avoid galvanized steel and vinyl for homes within a few miles of the ocean due to accelerated wear.
Seamless gutters are custom-fabricated on-site to the exact length of each run, which means no joints or seams where leaks typically develop. In Oregon's heavy-rain climate, those seam leaks can cause serious fascia rot and foundation damage over time. Seamless gutters also look cleaner, require less maintenance, and last significantly longer than sectional systems.
Most Oregon homes do best with 5-inch K-style gutters paired with 3x4-inch downspouts. Homes with steep roof pitches, large roof areas, or heavy runoff zones often benefit from 6-inch gutters and oversized downspouts. We calculate the right size based on your roof's square footage and pitch during the estimate.
We recommend 6-inch gutters for homes with large roof areas, steep pitches above 6/12, or heavy tree cover that increases debris load. Many Central Coast homes benefit from 6-inch gutters because Oregon's intense rainfall can overwhelm standard 5-inch systems during peak storms.
K-style gutters have a flat back and a decorative front that resembles crown molding — they are the most common profile in the U.S. and handle high water volume well. Half-round gutters are semicircular and offer a more traditional, elegant look popular on Craftsman and historic Oregon homes. Both perform well in our climate; K-style holds slightly more water per linear foot.
Half-round gutters are actually easier to clean because debris does not get trapped in flat corners the way it can in K-style profiles. However, half-round gutters hold less water per inch and require specialized brackets, which makes installation slightly more involved. Both styles work well on the Central Coast.
Box gutters are built into the roof structure rather than hung on the outside edge. They are common on older commercial buildings and flat-roofed structures. We can repair and reline box gutters, and we also convert them to external seamless systems when the existing box gutter has failed beyond repair.
Six-inch gutters should be paired with 3x4-inch rectangular downspouts or 4-inch round downspouts for proper flow capacity. Undersized downspouts create a bottleneck that defeats the purpose of larger gutters. We calculate the correct downspout sizing and placement during every estimate.
Most residential gutter installations are completed in a single day, typically 4 to 8 hours depending on the size of your home. Larger homes or complex rooflines with multiple stories may require a second day. We fabricate your seamless gutters on-site, so there is no waiting on materials to arrive.
We bring a portable gutter machine on our truck that rolls flat aluminum coil into a continuous, seamless gutter profile right in your driveway. Each piece is cut to the exact length of your roofline, eliminating joints where leaks typically start. The process is quick, clean, and means your gutters are custom-fit to your home.
You do not need to be home as long as we can access the full perimeter of your house. We typically confirm details and walk through the job before starting, so being present at the beginning is helpful. We will call you when the job is complete and walk you through the finished work.
Light rain does not stop our crew — we work through typical Oregon drizzle without issue. If a heavy storm rolls in, we may pause installation temporarily to ensure proper sealant adhesion and safe working conditions on ladders. We always monitor the forecast and will communicate with you in advance if we need to reschedule.
Our crews use drop cloths and take care to protect your landscaping. Ladders are placed on stable ground and we clean up all debris, metal shavings, and old gutter material when the job is done. If plants need to be temporarily moved, we will discuss that with you beforehand.
Yes. We install gutters year-round on the Central Coast. Winter is actually one of our busiest seasons because homeowners notice gutter problems once the heavy rains start. We work through typical Oregon winter weather and only reschedule for severe storms or unsafe conditions.
Steep roofs require specialized safety equipment, roof jacks, and sometimes scaffolding to ensure a safe and accurate installation. We also factor in the higher water velocity that comes off steep pitches and may recommend 6-inch gutters or additional downspouts to handle the increased flow.
Yes. Old gutter removal and disposal are included in every full installation quote. We carefully detach old gutters and downspouts, inspect the fascia underneath for rot or damage, and haul everything away. Aluminum gutters are recycled whenever possible.
As a general rule, you need one downspout for every 20 to 30 linear feet of gutter. Homes with large roof areas, steep pitches, or heavy rainfall exposure may need additional downspouts. We calculate the exact number and placement during your estimate based on your roof's square footage and Oregon's rainfall intensity.
Yes. Metal roofs require special brackets and standoff mounts because the gutter hangers cannot penetrate the metal panels the same way they attach to wood fascia. We have experience installing gutters on standing seam and corrugated metal roofs throughout the Central Coast.
Yes. Mobile and manufactured homes have different fascia and eave construction than stick-built homes, so they require specialized mounting brackets. We install seamless gutters on manufactured homes throughout Lincoln County and surrounding areas and ensure proper drainage away from the home's perimeter.
Please move any vehicles, patio furniture, or potted plants away from the house perimeter so our crew has clear access. Trim back any branches that hang directly over the roofline if possible. If you have dogs, please keep them inside or in a fenced area away from where we will be working.
In the Pacific Northwest, we recommend cleaning your gutters at least twice a year — once in late fall after the leaves drop and once in early spring. Homes surrounded by Douglas fir, cedar, or other conifers may need a third cleaning in midsummer since needles and pollen accumulate faster than broadleaf debris.
Neglected gutters clog with leaves, needles, and moss, causing water to overflow and pour down your siding and foundation. Over time this leads to fascia rot, foundation erosion, basement moisture, mold growth, and even structural damage. In Oregon's wet climate, the consequences of neglected gutters show up faster than in drier regions.
Common signs include water overflowing the edges during rain, visible plant growth in the gutters, sagging or pulling away from the fascia, water stains on exterior walls, and birds or pests nesting in the trough. If you see any of these, it is time for a cleaning.
Keeping gutters clean and ensuring proper water flow is the best prevention. Zinc or copper strips installed along the roof ridge can also inhibit moss growth as rainwater washes trace amounts of metal into the gutters. Trimming overhanging branches to increase sunlight exposure also helps, especially in shady areas common around Siletz and Toledo.
Pine and fir needles are small enough to slip through basic gutter screens and accumulate into dense, water-blocking mats. This is one of the most common gutter problems on the Central Coast where Douglas fir and Sitka spruce surround many homes. A micro-mesh gutter guard is the most effective solution for needle-heavy properties.
Yes. Standing water in clogged gutters is a breeding ground for mosquitoes. Accumulated debris also attracts birds, squirrels, rats, and wasps looking for nesting material or shelter. Keeping gutters clean and installing guards helps keep pests away from your roofline.
Gutter cleaning is one of the most common causes of ladder-related injuries for homeowners. Two-story homes, steep lots, and wet conditions — all common on the Central Coast — increase the risk significantly. We recommend professional cleaning, especially for multi-story homes or any situation where ladder placement is difficult.
A garden hose inserted from the top of the downspout can clear minor clogs. For stubborn blockages, a plumber's snake or pressure washer may be needed. If water backs up and will not drain, the clog may be in an underground extension or elbow. We clear clogged downspouts as part of our gutter cleaning service.
Gutter guards are covers or screens that keep leaves, needles, and debris out of your gutters while letting water flow through. In Oregon, where heavy rainfall meets heavy tree cover, they are absolutely worth it — they dramatically reduce clogging, overflow, and the frequency of cleanings. Our BroGuard micro-mesh system is designed specifically for the fine debris common in the PNW.
BroGuard is our proprietary micro-mesh gutter guard designed specifically for Pacific Northwest conditions. It features a stainless steel mesh over an aluminum frame that blocks needles, leaves, moss, and shingle grit while allowing maximum water flow. It comes with a lifetime no-clog guarantee and is installed by our trained crew.
Micro-mesh gutter guards with a fine stainless steel screen are the most effective at blocking pine and fir needles. Our BroGuard system uses a surgical-grade mesh that stops even the smallest needles and Sitka spruce debris common on the Central Coast while still handling Oregon's heaviest rainfall.
Yes, as long as your existing gutters are in good structural condition. We inspect your gutters during the estimate and can install guards on any properly functioning system. If we find sections that need repair or replacement, we recommend fixing those first to get the best performance from your guards.
Screen guards have large openings that block leaves but let needles and small debris through. Mesh guards use a finer material that blocks most debris but can clog with shingle grit. Solid surface guards rely on water adhesion and can fail in heavy Oregon downpours. Micro-mesh combines the best qualities of all three.
Gutter guards dramatically reduce how often cleaning is needed, but they do not eliminate it completely. Fine debris, pollen, and shingle grit can still accumulate on top of or inside the guards over time. With our BroGuard system, most homeowners go from twice-yearly cleanings to once every two to three years.
Quality gutter guards like our BroGuard micro-mesh system last 20 to 25 years or more. Cheaper plastic or foam guards may degrade in 3 to 5 years under Oregon's UV exposure and heavy moisture. We recommend investing in a durable system to avoid repeated replacement costs.
A properly designed gutter guard system handles even the heaviest Central Coast downpours. The key is surface tension and water volume capacity — cheap guards can cause water to sheet over them during intense rain. Our BroGuard system is tested for high-volume rainfall and handles the worst Oregon throws at it.
Gutter guards prevent debris from entering the gutter trough, but heavy moss accumulation on the guard surface itself can reduce water flow. We recommend periodic inspection and a quick brush-off of the guard surface, especially for homes under dense tree canopy in areas like Siletz and Toledo where moss grows aggressively.
Downspouts should discharge water at least 4 to 6 feet away from your foundation, directed toward a slope or drainage area that carries water away from the house. In the saturated soils common along the Central Coast, we often recommend underground extensions that route water even further from the structure.
Yes. We install above-ground extensions, splash blocks, and underground drainage lines to carry water safely away from your foundation. This is one of the most cost-effective things you can do to protect your home from water damage, especially in the wet soils around Newport and Waldport.
An underground system connects your downspouts to buried PVC pipes that route water to a pop-up emitter, dry well, or storm drain away from your home. This keeps your yard clear of above-ground extensions while providing superior foundation protection. It is especially valuable on the Central Coast where soil saturation is common.
Splash blocks, river rock beds, or underground extensions all help prevent soil erosion where downspouts discharge. Without protection, concentrated water flow carves channels in your landscaping and can undermine walkways and patios. We address drainage solutions during every gutter installation.
Yes. Connecting downspouts to an existing French drain is an excellent way to manage roof runoff, especially on properties with drainage challenges. We can tie into your French drain system or recommend a drainage contractor if one needs to be installed first.
Rain chains are decorative chains or cups that guide water down from the gutter to the ground. While visually appealing, they do not handle the heavy water volume that Oregon's rainy season produces. We recommend traditional downspouts for reliable performance and can install rain chains as a decorative supplement on covered areas with low water volume.
We recommend a minimum of 4 to 6 feet from your foundation, but 8 to 10 feet is ideal, especially in the saturated clay soils common on the Central Coast. Underground extensions can route water 15 feet or more from the structure for maximum foundation protection.
Oregon's Central Coast receives 60 to 80 inches of rain annually, which puts extreme demand on gutter systems. Undersized gutters, clogged downspouts, or insufficient slope cause overflows that damage fascia, siding, and foundations. Properly sized seamless gutters with adequate downspouts handle even our heaviest storms.
Freezing is uncommon along the immediate coast, but homes at higher elevations near Siletz, Toledo, and the inland valleys can experience occasional freezing. Well-installed gutters with proper slope drain before water can freeze. We do not typically recommend heat cables for coastal homes, but they are an option for inland properties.
Yes. Strong coastal winds, especially during winter storms, can loosen gutters, bend hangers, and even tear sections off the fascia. We use heavy-duty hidden hangers spaced closer together on exposed coastal homes to resist wind uplift. If you experience storm damage, call us for a free repair assessment.
Moss on your roof breaks off in chunks that clog gutters and downspouts. It also holds moisture against shingles, accelerating roof decay and increasing the debris load on your gutter system. Keeping moss off your roof and installing gutter guards significantly reduces gutter maintenance on moss-prone Central Coast homes.
Ice dams are rare on the immediate coast where temperatures stay mild, but they can occur during cold snaps, especially on north-facing roofs and in foothill areas near Toledo and Siletz. Proper attic insulation and ventilation are the best prevention. Gutters in good condition with adequate slope also help by not trapping water that could freeze.
Salt air does accelerate corrosion on vulnerable metals, particularly galvanized steel and exposed iron fasteners. Aluminum and copper hold up well against salt spray. We use stainless steel fasteners and marine-grade sealants on all coastal installations to ensure long-term durability in the salt zone.
Ensuring your gutters are securely fastened with heavy-duty hidden hangers is the best storm protection. Keeping gutters clean prevents added weight from wet debris that stresses connections during wind. After any major storm, a quick visual inspection can catch loose sections before they become bigger problems.
Yes. We repair leaks, reattach sagging sections, fix separated joints, replace damaged downspouts, and address storm damage. If a full replacement is not necessary, we will tell you — we only recommend replacement when repairs would cost more than new gutters or when the existing system is beyond saving.
Common signs include visible rust or corrosion, gutters pulling away from the fascia, persistent leaks at seams, standing water or sagging sections, peeling paint or water stains on your siding, and pooling water near your foundation. If you notice any of these issues, we recommend a free inspection before the next Oregon rain season.
The most common causes are clogged gutters or downspouts, insufficient gutter size for your roof area, improper slope, or too few downspouts. On the Central Coast, needle and moss buildup is usually the culprit. A free inspection can pinpoint the exact cause and we will recommend the most cost-effective fix.
Gutters pull away when hangers fail, fascia wood rots, or the weight of water and debris exceeds what the mounting system can support. This is especially common on older homes with spike-and-ferrule hangers. We reattach gutters with heavy-duty hidden hangers that screw into the rafter tails for a stronger hold.
In most cases, yes. We can splice in a new section of seamless gutter to replace a damaged area without redoing the entire run. However, if your gutters are old and showing widespread wear, a full replacement is often more cost-effective than repeated patchwork repairs.
Water stains usually mean your gutters are overflowing, leaking at a seam, or the back edge is not properly sealed against the fascia. Splashback from clogged or undersized downspouts can also cause staining. We identify the source during a free inspection and recommend the right repair.
Sagging gutters can usually be repaired by replacing failed hangers and reinstalling the gutter at the correct slope. If the gutter material itself is bent, warped, or corroded, replacement of that section is more practical. We always try the repair first and only recommend replacement when it makes financial sense.
Your downspouts may be discharging too close to the foundation, the downspout extensions may be missing or disconnected, or your gutters may be overflowing due to clogs. Underground drainage issues can also cause pooling. We check the entire system from gutter to ground discharge during every inspection.
Gutters should slope toward each downspout at approximately one-quarter inch per 10 feet of run. If water pools and stands in your gutters after rain stops, the slope may be off. We check and correct gutter slope during installations and can re-slope existing gutters that are draining improperly.
Yes. We handle commercial gutter projects including retail buildings, office complexes, multi-unit housing, and agricultural structures throughout the Central Coast. Commercial projects often require larger gutter profiles and industrial-grade materials, and we have the equipment and experience to handle them.
Commercial gutters are typically larger (6-inch or custom box profiles), use heavier gauge material, and are mounted with industrial-grade hangers designed to handle the greater roof area and water volume of commercial buildings. The installation process is also more complex and may require lifts or scaffolding.
Yes. We work with property managers, landlords, and HOAs across Lincoln County and the surrounding area. We can coordinate multi-unit installations, provide bulk pricing, and schedule work around tenant needs. We also offer maintenance agreements for ongoing gutter cleaning and inspection.
Every installation includes our workmanship warranty plus the manufacturer's material warranty. Aluminum gutters typically carry a 20-year or lifetime material warranty, and our BroGuard gutter guards come with a lifetime no-clog guarantee. We stand behind our work and will come back to make it right if anything goes wrong.
Yes. Brothers Gutters Oregon is a licensed Oregon contractor and carries full general liability insurance and workers' compensation coverage. We are happy to provide proof of insurance to any homeowner or property manager upon request.
Many homeowners insurance policies cover gutter damage caused by storms, falling trees, or other sudden events. Normal wear and tear is typically not covered. We recommend filing a claim with your insurance provider and can provide documentation, photos, and estimates to support your claim.
Our workmanship warranty covers defects in installation including improper slope, loose hangers, leaking connections, and any issue resulting from how the gutters were installed. It does not cover damage from acts of nature, lack of maintenance, or modifications made by others after installation.
Our manufacturer material warranties typically transfer to the new homeowner. Workmanship warranty transferability depends on the specific terms of your installation agreement. Contact us when selling your home and we will provide documentation for the new owner.
While basic sectional gutters can be a DIY project, seamless gutters require professional equipment to fabricate on-site. Professional installation ensures correct slope, secure mounting, and proper drainage — all critical in Oregon's heavy-rain climate. DIY sectional systems also leak at every seam, which causes problems faster in our wet weather.
The biggest risks are ladder falls, incorrect slope causing standing water, inadequate fastening that leads to sagging or detachment, and seam leaks that damage your fascia and foundation. Improper installation often costs more to fix than professional installation would have cost from the start.
Sectional gutters from hardware stores come in 10-foot sections that must be joined with connectors. Each joint is a potential leak point. Seamless gutters are one continuous piece custom-cut to your home, eliminating seam leaks entirely. In Oregon's climate, those seam leaks lead to rot, mold, and foundation damage within just a few years.
In most Oregon jurisdictions, residential gutter installation does not require a building permit. However, if the project involves structural modifications to your fascia or roofline, a permit may be needed. We handle all code compliance considerations and will advise you if a permit is required for your specific project.
Oregon building code does not universally require gutters on all residential structures, but many local jurisdictions and HOAs mandate them. Regardless of code requirements, gutters are essential on the Central Coast to protect foundations from our 60-plus inches of annual rainfall and to prevent soil erosion.
Lincoln County follows the Oregon Residential Specialty Code for building standards. Specific gutter requirements may vary by municipality and subdivision. We are familiar with local building requirements across the Central Coast and ensure all installations meet or exceed applicable codes.
Schedule a thorough gutter cleaning in late October or November after the leaves have dropped. Check for loose hangers, sagging sections, and leaks at seams or corners. Make sure all downspouts are clear and discharging away from the foundation. Addressing these issues before the heaviest rains prevents costly water damage.
Spring is ideal for inspecting your gutters after winter storm season. Look for sections loosened by wind, debris accumulation from winter storms, and any new leaks. Clean out leftover needles and moss, and check that downspout extensions are still properly directed away from your foundation.
We install gutters year-round, but late spring through early fall offers the most predictable weather for scheduling. That said, fall is our most popular season because homeowners want new gutters in place before the heavy rains arrive. Book early in September to secure your preferred installation date.
Both. A fall cleaning before storm season ensures your gutters can handle winter rains without overflowing. A spring cleaning afterward removes debris accumulated during winter. This twice-yearly schedule is the minimum we recommend for Central Coast homes.
Yes. We have experience working with historic and Craftsman-style homes throughout the Central Coast. Half-round copper or aluminum gutters are popular choices that complement these architectural styles. We take extra care to preserve period details and can match profiles that are appropriate to your home's era.
Not always. Some builders include gutters in the construction package, but many new homes are delivered without them, leaving the homeowner to arrange installation separately. If you are building a new home on the Central Coast, we can coordinate with your builder to install gutters at the ideal point in construction.
Multi-story homes require taller ladders, additional safety equipment, and sometimes scaffolding or boom lifts. The cost is higher due to the extra labor and equipment, but the installation process and quality are the same. We regularly work on two and three-story homes in Newport, Lincoln City, and surrounding areas.
Homes surrounded by trees face higher debris loads, faster moss growth, and more frequent clogs. We typically recommend 6-inch gutters, additional downspouts, and our BroGuard micro-mesh gutter guards for heavily wooded properties. More frequent cleaning schedules may also be necessary, especially for homes under Douglas fir or Sitka spruce canopy.
Yes. Complex rooflines with dormers, valleys, multiple levels, and intersecting planes are common on the Central Coast. These homes require careful planning to route water effectively through multiple gutter runs and downspouts. We assess the entire roofline during your estimate and design a system that handles every section.
Yes. Oregon law allows residential rainwater collection from rooftop surfaces without a permit. With 60 to 80 inches of annual rainfall on the Central Coast, rainwater harvesting is highly practical for garden irrigation and other non-potable uses. We can install diverters that route water to rain barrels or cisterns.
Yes. Aluminum is 100 percent recyclable and retains its properties through the recycling process. When we remove old aluminum gutters, we take them to a local recycling facility rather than sending them to the landfill. Copper gutters are also highly recyclable and have significant scrap value.
Without gutters, rainwater falls directly off the roof edge and pounds the soil around your foundation, creating trenches and washing away landscaping. Gutters collect that water and route it through downspouts to controlled discharge points, preserving your soil, mulch, and plantings while protecting your foundation from erosion and settling.
Yes. We install rain barrel diverters that redirect downspout water into collection barrels during dry months and bypass them when the barrels are full. This is a popular option on the Central Coast for homeowners who want to water gardens during our relatively dry summers using water collected during the rainy season.
We serve homeowners across Oregon's Central Coast and surrounding communities including Siletz, Newport, Lincoln City, Waldport, Toledo, Depoe Bay, Corvallis, Albany, and Salem. Our focus is the Central Coast — give us a call and we'll let you know if we can reach you.
Yes. Newport is one of our primary service areas. We install, repair, and clean gutters throughout Newport, including the Bayfront, Nye Beach, South Beach, and Agate Beach neighborhoods. Our Siletz location is just a short drive from Newport, allowing us to respond quickly.
Yes. We provide full gutter services throughout Lincoln City and the surrounding communities of Gleneden Beach, Depoe Bay, and Neskowin. Whether you need new seamless gutters, repairs, cleaning, or gutter guards, we serve the entire northern Lincoln County coastline.
Yes. We serve Waldport, Yachats, and the communities along Highway 101 south of Newport. The southern Central Coast gets heavy rainfall and has many homes nestled in dense forest, making quality gutters and gutter guards especially important in that area.
Our service area extends inland to Corvallis, Albany, and Salem. We regularly work in Toledo, Siletz, Eddyville, and other communities between the coast and the Willamette Valley. If you are unsure whether we reach your area, give us a call and we will let you know.
If your gutters are more than 15 years old or showing signs of wear, coordinating replacement with a new roof is smart because the roofers will remove portions of your gutter system anyway. Installing new gutters after the new roof ensures a perfect fit and allows us to inspect and repair the fascia while it is fully exposed.
It is common for roofing crews to detach, bend, or damage gutters during a roof replacement, even when they try to be careful. If your gutters are newer and in good condition, ask your roofer to carefully remove and reattach them. If damage occurs, we can repair or replace the affected sections after the roof work is complete.
Gutters collect roof runoff and direct it away from your foundation through downspouts and drainage extensions. Without gutters, water cascading off the roof saturates the soil next to your foundation, causing erosion, hydrostatic pressure, and eventually cracks, settling, or basement flooding — all accelerated by Oregon's heavy annual rainfall.
Yes. Gutters that overflow, leak, or discharge too close to the foundation allow water to pool around the base of your home. Over years, this saturates and expands the soil, creating pressure that cracks concrete foundations and compromises structural integrity. Fixing your gutters is one of the most affordable ways to prevent expensive foundation repairs.
Fascia is the vertical board that runs along the lower edge of your roof where gutters are mounted. If the fascia is rotted, soft, or damaged, your gutters cannot be securely attached and will sag or pull away. We inspect fascia on every job and recommend repair or replacement before installing new gutters if needed.
Yes. Rotted fascia is one of the most common issues we find during gutter estimates on the Central Coast, where moisture exposure is constant. We remove the damaged fascia, install new treated or composite fascia board, and then mount your gutters to a solid, long-lasting surface.
Soffit is the underside of your roof overhang. When gutters overflow or leak behind the gutter trough, water runs onto and behind the soffit, causing staining, rot, mold, and eventually structural damage to the eave. Properly functioning gutters protect your soffit from water exposure.